REPAIR PROCEDURES HOW TO USE THIS MANUAL To assist you in finding your way through the manual, the Section Title and major heading are given at the top of every page. PREPARATION Preparation lists the SST (Special Service Tools), recommended tools, equipment, lubricant and SSM (Special Service Materials) which should be prepared before beginning the operation and explains the purpose of each one. Most repair operations begin with an overview illustration. It identifies the components and shows how the parts fit together. Example: AT8669Non-reusable part N-m (kgf-cm, ft-lbf): Specified torqueO-Ring Oil Seal Drive Gear Thrust Washer Oil Seal Ring Driven Gear 10 (100, 7)Pump BodyStator Shaft IN-2-INTRODUCTIONHOW TO USE THIS MANUAL ffYDeùííím^l}fí”W[ shenduauto/ [gQQQ1398556747 u5íí18218750259 (a)Place SST and a dial indicator onto the overdrive brake piston as shown in the illustration. SST09350-30020 (09350-06120) The procedures are presented in a step-by-step format: RThe illustration shows what to do and where to do it. RThe task heading tells what to do. RThe detailed text tells how to perform the task and gives other information such as specifi- cations and warnings. Example: This format provides the experienced technician with a FAST TRACK to the information needed. The upper case task heading can be read at a glance when necessary, and the text below it provides de- tailed information. Important specifications and warnings always stand out in bold type. REFERENCES References have been kept to a minimum. However, when they are required you are given the page to refer to. SPECIFICATIONS Specifications are presented in bold type throughout the text where needed. You never have to leave the procedure to look up your specifications. They are also found at the back of AX section, for quick reference. Illustration: what to do and where Set part No. Piston stroke: 1.40 - 1.70 mm (0.0551 - 0.0669 in.) Task heading: what to do 21.CHECK PISTON STROKE OF OVERDRIVE BRAKE Component part No. Specification (b)Measure the stroke applying and releasing the com- pressed air ( 392 - 785 kPa, 4 - 8 kgf/cm2 or 57 - 114 psi) as shown in the illustration. Detail text: how to do task -INTRODUCTIONHOW TO USE THIS MANUALIN-3 ffYDeùííím^l}fí”W[ shenduauto/ [gQQQ1398556747 u5íí18218750259 CAUTIONS, NOTICES, HINTS: RCAUTIONS are presented in bold type, and indicate there is a possibility of injury to you or other people. RNOTICES are also presented in bold type, and indicate the possibility of damage to the compo- nents being repaired. RHINTS are separated from the text but do not appear in bold. They provide additional information to help you perform the repair efficiently. Sl UNIT The UNITS given in this manual are primarily expressed according to with the Sl UNIT (International System of Unit), and alternately expressed in the metric system and in the English System. Example: Torque: 30 N-m (310 kgf-cm, 22 ft-lbf) IN-4-INTRODUCTIONHOW TO USE THIS MANUAL ffYDeùííím^l}fí”W[ shenduauto/ [gQQQ1398556747 u5íí18218750259 IN0036 Seal Lock Adhesive FI1066 1.Use fender, seat and floor covers to keep the vehicle clean and prevent damage. 2.During disassembly, keep parts in the appropriate order to facilitate reassembly. 3.Observe the following: (a)Before performing electrical work, disconnect the negative cable from the battery terminal. (b)If it is necessary to disconnect the battery for in- spection or repair, always disconnect the cable from the negative (-) terminal which is grounded to the vehicle body. (c)To prevent damage to the battery terminal post, loosen the terminal nut and raise the cable straight up without twisting or prying it. (d)Clean the battery terminal posts and cable termi- nals with a clean shop rag. Do not scrape them with a file or other abrasive objects. (e)Install the cable terminal to the battery post with the nut loose, and tighten the nut after installation. Do not use a hammer to tap the terminal onto the post. (f)Be sure the cover for the positive (+) terminal is properly in place. 4.Check hose and wiring connectors to make sure that they are secure and correct. 5.Non-reusable parts (a)Always replace cotter pins, gaskets, O-rings and oil seals etc. with new ones. (b)Non-reusable parts are indicated in the compo- nent illustrations by the ” ” symbol. GENERAL REPAIR INSTRUCTIONS 6.Precoated partsPrecoated parts are bolts and nuts, etc. that are coated with a seal lock adhesive at the factory. (a)If a precoated part is retightened, loosened or caused to move in any way, it must be recoated with the specified adhesive. -INTRODUCTIONGENERAL REPAIR INSTRUCTIONSIN-5 ffYDeùííím^l}fí”W[ shenduauto/ [gQQQ1398556747 u5íí18218750259 。。。。。。